Jetway JNF9U-2930 mITX Motherboard

*** This item has an 8-week lead time from the factory, please call 714-252-4868 for express shipping ***

- Intel Celeron N2930 SoC Processor
- Embedded Class Planned Lifecycle through Q1'2021
- Supports up to 2 Displays, HDMI, VGA, 24bit LVDS
- RJ11 Jack with +12V/+24V Power for Cash Drawers
- 6 x COM Ports with +5V/+12V
- 9V ~ 24V DC-in or Alternate Internal 2-pin Power Connector
- ECO-design for EuP/ErP

Specification

Jetway NF9U Mini-ITX Motherboard
Processor	Intel® Celeron N2930 SoC, 1.83GHz ™€" 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP
Memory	1 x 204-pin DDR3L-1333 SO-DIMM up to 8GB (1.35V required)
Graphics	Intel HD Graphics, 313MHz - 854MHz
Audio	Realtek ALC662 2.1 Channel HD Audio with 3W Amplifier
LAN	2 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
Storage	2 x SATA2 3Gb/s Connectors 1 x mSATA (Full size)
Super IO	FINTEK F81866A
Back Panel Connectors
1 9V ~ 24V DC-In jack 1 USB 3.0 3 USB 2.0 1 PS/2 Keyboard/Mouse 1 RJ-11 port (+12V/+24V) 1 HDMI 1 VGA 1 Parallel port 1 COM port (RS232/422/485, +5V/+12V) 2 RJ45 LAN (10/100/1000) 2 3.5mm Audio Jacks (Line Out, Mic In)
Onboard I/O Connectors
1 PCI Express x1 Slot 1 Full size mSATA Slot 1 Half size mini PCI-E Slot 2 SATA2 3Gb/s Connectors 2 USB Pin Headers for up to 4 additional USB 2.0 Ports 5 Serial Port Headers (RS232, +5V/+12V) 1 24-bits Dual Channel LVDS connector/Inverter 1 AT/ATX power switch mode select jumper 1 Chassis Intrusion header 1 SMBUS header 1 8-bit GPIO header 1 9-pin Audio header 1 Front Panel header 3 Fan headers 1 2-pin +9 ~+24V Alternate Power Connector
Power Supply for NF9U
External Power Supply ™€" the board can be powered with a 9V ~ 24V external power supply though a DC connector on the back panel. The rear 9V ~ 24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 9V ~ 24V and the shell is GND. Internal Power Supply ™€" the board can alternatively be powered via the internal 9V ~ 24V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +9 ~ +24 (±10%) VDC. Caution: There is no isolation circuitry between the external 9 ~ 24 VDC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 9 ~ 24 VDC jack is covered if the internal 1 x 2 power connector is to be used.
Market Segments Supported
√ Digital Security & Surveillance √ Digital Signage √ Gaming √ Industrial Automation/Control √ Medical √ Retail (POS/Kiosk/ATM) √ Networking/Storage Server/Mail Server/Print Server √ Thin Client √ HTPC
Environment
Operating Temperature : 0 ~ 60°C Storage Temperature : -20 ~ 85°C