Jetway MI97-30UT Mini-ITX Industrial Motherboard

- Intel Celeron N2930 SoC Processor
- Long-Life Embedded Class with Planned Lifecycle Through Q1’2029
- A Successor to NF9T, a seamless transition with same IO Layout
- Supports up to 2 Display, HDMI, VGA, eDP or LVDS
- Gigabit LAN, 3 * M.2, 8 * USBs, 5 * COMs
- Built-in 12V DC Power Input, SIM Slot, PCI-E x1
- ECO-design for EuP/ErP   

Specification

Model Name	MI97
Part Number	MI97-30	MI97-32
Form Factor	Mini ITX (170 x 170mm)
Processor	Intel® Celeron N2930 SoC, 1.83GHz â€" 2.16GHz Burst, Quad-Core, 7.5W TDP
Memory	1 x 204-pin DDR3L-1333 SO-DIMM up to 8GB (1.35V required)
Graphics	Intel HD Graphics, 313MHz - 854MHz
Audio	Realtek ALC662 HD Audio Realtek ALC888 HD Audio (Manufacturered after April 2021)
LAN	1 x Intel I211-AT PCI-E Gigabit LAN
Storage	1 x SATA2 3Gb/s Connector 1 x M.2 SATA M-key 2242/2280 length
Super IO	FINTEK F81966D
TPM	Intel fTPM 2.0 (PTT) Trusted Computing Firmware	Intel fTPM 2.0 (PTT) Trusted Computing Firmware Onboard NUVOTON TPM v2.0
Back Panel Connectors
1 +12V 2.5mm Diameter DC Power Jack 1 HDMI (1920 * 1200 @ 60Hz) 1 VGA (1920 * 1200 @ 60Hz) 1 Parallel 3 USB 2.0 1 PS2 Mouse/Keyboard Combo 2 Serial Ports (1 * RS232, 1 * RS232/422/485) 1 RJ45 LAN (10/100/1000) 1 USB 3.0 2 3.5mm Audio Jack (Line Out & MIC In)
Onboard I/O Connectors
1 PCI-E x1 Slot 1 SATA2 3Gb/s Connector 1 M.2 M-Key, 2242/2280, SATA 1 M.2 E-key, 2230, for WiFi (USB 2.0/PCIE x1) 1 M.2 B-Key, 3042, with SIM Slot (USB 2.0) 3 Serial Headers (RS232) 2 USB Pin Headers for up to 4 additional USB 2.0 Ports 1 40-pin eDP (2560 * 1600 @ 60Hz) OR 24-bits Dual Channel LVDS/Inverter (1920 * 1200 @ 60Hz) 1 8 bit GPIO Header 1 AT/ATX Mode Jumper 1 9-pin Front Audio Header 1 5-pin SMBUS Header 1 4-pin Fan Header 1 4-pin SATA Power Output (Male) 1 2-pin +12V Alternate DC-in (Mating plug: Molex 5557-02R)
Power Supply for MI97
External Power Supply the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND. Internal Power Supply â€" the board can alternatively be powered via the internal +12V 2-pin power connector, where pin 1 is +12V and pin 2 is GND. The internal 2-pin power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply. Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2-pin power connector is to be used.
Market Segments Supported
√ Industrial PC √ Factory Automation √ Retail (POS/Kiosk/ATM) √ Panel PC √ IoT
Environment
Operating Temperature : 0 ~ 60°C Storage Temperature : -40 ~ 70°C Humidity: 10% ~ 90% RH @40°C (non-condensing)